New 1910 Tow-Behind Air Commodity Cart

John Deere
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Choice of auger or conveyor
  • Stationary single-shoot manifold
  • In-line drive system transfers power efficiently
  • New 550-bushel grain tank capacity on tow-behind models

More Info

Features

Efficient air system ensures consistent product delivery
Secondary manifolds
Secondary manifold on seeding toolSecondary manifold on seeding tool
One-piece removable lid with tetherOne-piece removable lid with tether

Secondary manifolds with 25-mm (1-in.) diameter lines evenly distribute the seed and/or fertilizer from the primary manifold(s) to the furrow openers.

 

Air systems are color coded (optional) in order to more conveniently connect the air distribution kit from the 1910 Cart to the seeding tool. Black hoses are typically used for seed and green hoses for fertilizer.

The 25-mm (1-in.) secondary lines are clear with a black spiral (clear with a green spiral is available with the double-shoot air kits).

The secondary manifold is made of durable, maintenance-free ethylene-propylene molded (EPDM) rubber. Features of the secondary manifold:

  • Rust resistant, important when applying fertilizer or treated seed
  • Easier to service with an easy-to-remove lid, no tools required
  • No long bolt in the secondary tower
  • Lid is tethered to the manifold
  • The outlet ports are numbered

 

High-output, hydraulically driven fanHigh-output, hydraulically driven fan
Fan as seen on 19,400-L (550-bu) cartFan as seen on 19,400-L (550-bu) cart

The 1910 Commodity Air Cart uses an airstream to gently deliver seed and/or fertilizer to the openers. A strong, consistent airstream is necessary to keep product moving without plugging the air runs, while making sure damage is not occurring to the seed.

 

The large 450-mm (17.6-in.) diameter fan generates a low-velocity, high-volume airstream that carries the product to the openers. By using a high volume of air, there is less chance of damaging seed, while decreasing the likelihood of plugging the air system.

 

The fan is driven by the tractor's hydraulic system. It requires approximately 53- to 75-L/min
(14 to 26-gpm) oil flow for operation.

 

IMPORTANT: The 53- to 75-L/min (14- to 26-gpm) is for the 1910 Cart fan only; additional hydraulic capacity from the tractor is also required for the hydraulic drive motors and for the seeding tool, depending on what seeding tool is chosen.

 

NOTE: Requires motor seal drain kit.

Primary manifolds
Stationary double-shoot primary manifoldStationary double-shoot primary manifold
#

Primary manifolds are mounted below the tanks with 63.5-mm (2-1/2-in.) diameter tubes to distribute seed/fertilizer evenly to the secondary manifolds, which are located on the seeding tool. 

63.5-mm (2-1/2-in.) primary lines are clear with either a black or green spiral:

  • Black spiral for single-shoot systems
  • Black and green spiral for double-shoot systems

 

Stationary single-shoot or stationary double-shoot primary manifolds are available.

 

Single-shoot air systems are used when seeding only or when applying a starter fertilizer along with the seed. Double-shoot air systems are used when applying higher levels of fertilizer, allowing simultaneous application of seed and fertilizer by placing them in two different locations in the seed row. With the proper 1910 Cart configuration, starter fertilizer can also be applied with the seed in a double-shoot air system.

Ten 1910 Cart choices fit any farming operation

Growers around the world are always looking for ways to become more productive. The John Deere Seeding Group is continually looking for ways to help these growers increase productivity.

 

The 1910 Commodity Cart is one of the best ways to maximize productivity. By providing growers with several different tank configurations, the 1910 Cart allows growers to get the most benefit from input costs and time in the field.

 

The tanks are a semi-transparent, poly material. Owner benefits include:

  • Corrosion resistance
  • Ease of quickly viewing tank level from outside the cart
  • Lightweight, increasing cart floatation
Large-capacity, two-tank 1910Large-capacity, two-tank 1910
Three tanks increase productivity and efficiencyThree tanks increase productivity and efficiency

Tow-behind capacity

Two tanks

 Total

Bushel

270

120

150

 

Litres

9500

4200

5300

 

Tonnes

7.2

3.2

4.0

 

Bushel

350

150

200

 

 

Litres

12,300

5300

7000

 

Tonnes

9.4

4.0

5.4

 

Three tanks

 Total

Bushel

340

120

70

150

 

Litres

12,000

4200

2500

5300

Tonnes

9.1

3.2

1.9

4.0

Bushel

430

150

80

200

 

Litres

15,200

5300

2800

7000

Tonnes

11.5

4.0

2.1

5.4

Bushel

550

200

150*

200

Litres

19,400

7000

5300

7000

Tonnes

17.2

5.4

4.0

5.4

Tow-between capacity

Two tanks

 Total

Bushel

270

120

150

 

Litres

9500

4200

5300

 

Tonnes

7.2

3.2

4.0

 

Bushel

350

150

200

 

 

Litres

12,300

5300

7000

 

Tonnes

9.4

4.0

5.4

 

Three tanks

 Total

Bushel

250

75

55

120

 

Litres

8800

2600

1900

4200

Tonnes

6.6

2.0

1.4

3.2

Bushel

430

150

80

200

 

Litres

15,200

5300

2800

7000

Tonnes

11.5

4.0

2.1

5.4

*Assumptions: cubic metre (1000 litres) of: wheat (front tank) = 0.76 tonnes, urea (middle tank) = 0.73 tonnes, fertilizer (rear tank) = 1.10 tonnes, bushel = 35.3 litres.

The tank lids are sealed, ensuring proper air pressure within the tank and at the meters. Sealing the tanks improves hydraulic fan utilization, providing efficient and optimum seeding accuracy. 

 

With less than 0.13 bar (2 psi) of pressure in the tank, the pressure is equalized between the meters and tanks, providing an accurate, consistent seeding rate.

NOTE: Tank volume is measured to heaped capacity. When product is shoveled to the corners of the tank, the tanks may hold more than advertised capacity.

SectionCommand™ system saves seed and fertilizer input costs
SectionCommand controls seed and fertilizer overlaps and skips

Controlling input costs and improving productivity are key producer requirements today. SectionCommand is an effective, integrated John Deere solution designed to meet these intensifying needs. SectionCommand manages both seed and fertilizer application by minimizing overlaps and skips while seeding with the John Deere 1910 Air Cart.

 

Owner benefits include:

  • Improved consistency of crop maturity at harvest
  • Improved consistency during emergence and growing season
  • Reduced seed input cost
  • Reduced fertilizer input cost
  • Increased time between fills due to input savings

SectionCommand is optional factory-installed equipment on all John Deere 1910 Air Carts. When the option is selected, each tank and meter will receive SectionCommand components. A two-tank cart will control sections out of both tanks and three-tank carts will control sections out of all three tanks. SectionCommand is also available as an attachment for field conversion (AFC) for all hydraulic drive carts. See AFC kit story for more information.

 

SectionCommand controls seed and fertilizer output by closing and opening gates on the bottom side of the meter. When the gates are open, commodity is metered out, and when closed, commodity stays and continues to rotate within the meter. The meter stays full at all times so immediately when the gate opens, the commodity can flow into the primaries and onto the tool. Since each meter section has its own gate, application rates and row-to-row accuracy are not compromised. The gates are utilized to control commodity output on all sections. Once the last gate needs closed, the entire meter will stop turning, stopping product flow.

Seeded fields photo Seeded fields photo
#

When commanded, electric over-hydraulic solenoids engage actuators to instantaneously close the gate for the needed section. The actuators are powered via hydraulics from the same circuit as the hydraulic drive motors. When power is cut, oil is diverted to retract the actuators and open the gates. The retraction is both powered and spring assisted, so it will always default to the seeding position. The oil from SectionCommand drains back through the fan motor case drain line and is coupled with an accumulator on the valve block to provide extra drainage capacity.

SectionCommand components as seen on back side of meterSectionCommand components as seen on back side of meter
SectionCommand components as seen on front side of meterSectionCommand components as seen on front side of meter

SectionCommand incorporates gate detection, which gives producers the satisfaction of knowing the gates are in position as commanded. Magnets on the back side of the gates are used in close proximity to the gate detection sensors to determine if the gates are open or closed. Should a gate not be in the commanded position, an alarm will alert the operator of the gate(s) in question. The blockage warning system works in conjunction with SectionCommand to give further confidence whether a given section is seeding or not when commanded.

Orange roller, for use only with large seeds and SectionCommandOrange roller, for use only with large seeds and SectionCommand
SectionCommand meter cartridge showing one gate closed and magnet on backside of gateSectionCommand meter cartridge showing one gate closed and magnet on backside of gate
Gate detection sensorGate detection sensor

For maximum performance, SectionCommand should be controlled through John Deere Section Control on the GreenStar™ 3 (GS3) 2630 Display. Coupling SectionCommand with John Deere Section Control provides the ultimate in precision seeding and productivity. If a Section Control activation is held by the producer, that same activation can be utilized for SectionCommand.

 

SectionCommand introduces the orange roller, which has the same number of flutes and spacing as the blue roller, but shorter flutes. It is for use only with SectionCommand when seeding seeds larger than 6 mm (0.25 in.) in diameter (soybeans, chick peas, etc.). The orange roller is not for use with cereal grains or fertilizer.

SectionCommand™ savings calculator assists operators in determining potential savings

To assist in determining savings potential for an operation when using SectionCommand, please utilize the savings calculator. A link is provided for access to the calculator.

 

Directions:

 

The savings calculator can calculate savings potential for up to three crops.  Insert the variables into the yellow boxes for each of the three crops.  Input variables include:

  • Crop(s)
  • Acres of each crop
  • Seeding rate per acre
  • Seed price per pound
  • Fertilizing rate per acre
  • Fertilizing rate per pound

Green boxes will list the potential savings per crop and total savings are listed at the bottom of the page.

Enable documentation of farming operations with Field Doc™ data collection system

Field documentation is part of the Basics package and comes as standard equipment on the GreenStar™ 3 (GS3) 2630 Display. Field documentation allows customers to document operations in the field. Those operations include: 

  • Tillage 
  • Nutrient application 
  • Planting 

All data is collected on the display and can later be reviewed in Apex™ farm management software or the John Deere Operations Center, where it can be shown in the form of maps and reports.

Tillage documentation with GS3 system
TillageTillage
#

The GS3 2630 Display can be used to document tillage operations. The tillage information can be unloaded into Apex farm management software to create maps and reports.

John Deere sprayer and spreader documentation with GS3 system
John Deere sprayerJohn Deere sprayer
#

The GS3 2630 Display can be used to document product applications on John Deere sprayers and spreaders. The application data can be unloaded into the John Deere Operations Center or Apex farm management software for reporting information.

Planter documentation with GS3 system
John Deere planterJohn Deere planter
#

Operators can use the GS3 2630 Display to document seeding rates and varieties and instantaneously field data is written to the display which can later be used to make more informed decisions.

Collected data may include:

 

Tillage

Nutrient App

Planting

Farm name

X

X

X

Field name

X

X

X

Tillage depth

X

N/A

N/A

Application rates

N/A

X

N/A

Seeding rates

N/A

N/A

X

Variety

N/A

N/A

X

Totals

X

X

X

Machine

X

X

X

Implement

X

X

X

Operator name

X

X

X

Field boundaries

X

X

X

Weather conditions

X

X

X

Soil temperature

X

X

X

Required components

   

  • GS3 2630 Display
  • StarFire™ Receiver or third-party global positioning system (GPS) receiver
  • Apex desktop software
  • Compatible machine
  • GS3 2630 Display
  • StarFire or third-party GPS receiver
  • Apex desktop software
  • Compatible planter
  • GS3 2630 Display
  • StarFire or third-party GPS receiver
  • Apex desktop software

 

 

Machine compatibility

  • R4045
  • R4038
  • R4030
  • R4023
  • 4930 SpreadStar™ system
  • 4830
  • 4920
  • 4730
  • 4940
  • 4720
  • 4710 (serial numbers 2000 and prior require the SprayStar Gen 4 upgrade)
  • 4700 (require the SprayStar Gen IV upgrade)
  • 4630
  • 6700 (serial numbers 8000 and prior require the SprayStar Gen 4 upgrade)

The GS3 2630 Display is capable of documenting up to six unique varieties.

  • For SeedStar™ planters with three hydraulic drives, one variety follows the left-most hydraulic motor. Another variety follows the two right motors.
  • For SeedStar planters with an equal number of hydraulic drives, varieties split following the left and right drives.
  • For non-SeedStar planters, the implement width is split in equal halves follows the left-most hydraulic motor. Another variety follows the two right motors.

 

Third-party compatibility with GS3 2630 system via Field Doc™ connect

Documentation of field operations remains important regardless of controller brand. The GS3 2630 Display is capable of communicating with selected third-party controllers. Collectively, the system supplies the operator with instantaneous data while logging it to a data card. This information can be downloaded into Apex Farm Management software for further analysis and reporting.

 

When using Raven, Rawson®, or New Leader® controllers, the Field Doc Connect system is also capable of running in conjunction with map-based prescriptions. 

 

DICKEY-john and Seed Manager are trademarks of DICKEY-john Corporation. New Leader is a trademark of Highway Equipment Company. Raven SCS 440, Raven SCS 450, Raven SCS 460, Raven SCS 660M, and Raven Sidekick are trademarks of Raven Industries Incorporated. Rawson, ACCU-RATE, and ACCU-PLANT are trademarks of Trimble Navigation Limited Corporation. Vanguard VM-2500 Precision Information Center and Vanguard VM-2500SE Precision Information are trademarks of Agri Motive Products, a division of the Daugherty Companies Incorporated. TeeJet is a trademark of Spraying Systems Company.

1910 Cart brakes
1910 Cart brakes1910 Cart brakes

Cart brakes are an option with 430 Tow Between, 430 Tow Behind, and 550 Tow Behind Carts. The brakes are required when using a 23-m (76-ft) 1870 tool.

 

The air cart hydraulic brake system connects to the tractor’s hydraulic system through a brake connection at the rear of the tractor. Tow behind carts require an extension hose for the air seeding tool.

 

The air cart brake system supplement the tractor brakes. The cart system senses when the tractor’s brakes are applied and engages a caliper on a rotor at each rear axle hub.

 

Ensure the tractor has a hydraulic brake port and is equipped with adequate ballast for the air cart and seeding tool.

Wireless controlled hydraulic conveyance reduces operator physical effort

Operators continually seek easier and faster operations while seeding and reduce time spent filling and unloading.

 

Conveyance on 350-bu, 430-bu, and 550-bu carts is now controlled by hydraulic cylinders on the conveyance arms. The cylinders move the main arm, swing arm, and elevation. Now operators can easily deploy the conveyance system with less effort.

 

Input to the system is received from one of two remotes. Each operator receives a wireless remote that can be operated from anywhere near the cart and a tethered remote that can be operated from ground level near the front meter. Each remote controls the same functions and gives flexibility of system control should two operators be in the area during cart fill and unload.

 

The remotes can start, stop, and control speed of the conveyance system. For added security, the speed control arm is retained on the conveyance and can override the remotes to slow down or stop the belt or auger.

Securing the auger or conveyor is now easier and gives the operator a greater sense of security with over-center latches on both the top and bottom of the conveyance.

 

Both the main and swing arms are longer giving operators greater flexibility in tendering vehicle parking locations.

Wireless remoteWireless remote
Receiver and tethered remoteReceiver and tethered remote
#

 

 

 

 

 

 

 

 

A - Remote on/off

B - Conveyance stop/start

C - Conveyance slow down/speed up

D - Tilt/Elevation

E - Main arm retract/extend

F - Swing arm retract/extend

Left-hand side of cart in transportLeft-hand side of cart in transport
Left-hand side of cart in fill positionLeft-hand side of cart in fill position
Left-hand side of cart in unload positionLeft-hand side of cart in unload position
Low-profile hopper folder and unfoldedLow-profile hopper folder and unfolded
Low-profile hopper folder and unfoldedLow-profile hopper folder and unfolded

Low-profile hopper

 

For operators who fill carts from semi hopper bottoms or who desire full width meter clean out, John Deere has partnered with KSi™ Conveyors to provide a low-profile hopper. The hoppers are compatible with all hydraulic conveyance carts. The hoppers utilize conveyor belts and are available for both the 255-mm (10-in.) auger and 305-mm (12-in.) conveyor. The hoppers are longer than competitive offerings on similar cart sizes.

 

The hoppers easily fold over to keep mud and rocks from being slung into the hopper and for tight maneuverability during transport and seeding. During fill and unload, flip the hoppers back over to move product.

 

Each hopper comes with both a large and small screen for optimizing product flow and catching foreign material during fills. Rubber skirting around the hopper provides flexibility during use and adds capacity to the hopper.

 

Please contact KSi Conveyors for ordering information.


KSi Conveyors Inc.
c/o Bruce Frank
1(888) 574-3277
+1(815) 457-2403
jddealer@ksiconveyors.com
http://www.ksiconveyors.com/jddealer

KSi is a registered trademark of KSi Conveyors, Inc.

Choice of auger or conveyor
255-mm (10-in.) auger on 15,200-L (430-bu) cart255-mm (10-in.) auger on 15,200-L (430-bu) cart
#

It is simple: Less time filling means more time seeding. As growers look for ways to increase efficiencies, one solution is to shorten the time required to fill. By increasing pit stop productivity, growers are able to cover more ground per day.

 

Producers have the choice of an auger or conveyor to fit their needs.

 

The 255-mm (10-in.) auger:

  • Available on the 12,300-L (350-bu), 15,200-L (430-bu), and 19,400-L (550-bu) carts
  • Loading rate 1800 L (50 bu) per minute
  • Balanced for safe, convenient movement between storage and filling positions
  • Able to fit under the meters for tank cleanout

The 200-mm (8-in.) auger:

  • Available on 8,800-L (250-bu), 9,500-L (270-bu), and 12,000-L (340-bu) carts
  • 700-L (20-bu) per minute fill rate
305-mm (12-in.) conveyor305-mm (12-in.) conveyor
#

For growers who need a gentle conveyance system.

The 305-mm (12-in.) conveyor:

  • 305-mm (12-in.) wide belt with risers spaced on 150 mm (6 in.)
  • 1400 L (40 bu) per minute fill rate
  • Can also transfer fertilizer
  • Cleanout  trap door at the bottom
  • Optional on all carts

The telescoping spout, which is standard equipment, provides the following benefits:

  • Decreases fill time
  • Easily fills each tank to the very top
  • Improves movement when going from one tank to another, matching the tank height
The metering system provides accuracy and convenience

A meter cartridge at each compartment (tank) effectively meters seed or fertilizer into the primary manifold. Air carries the material to the secondary distributor for delivery to the furrow openers on the seeding tool. 

 

Meters are contained in a cartridge for quick and easy removal and are color coded for quick and easy identification.

 

A half-width disconnect is incorporated into the meter system:

  • Allows one-half of the metering system to be manually shut off for irregular shaped headlands, point rows, etc. on mechanical drive carts.
  • Allows the meter cartridge to be removed with material still in the tank(s).
  • Allows tanks to be emptied with meter and primary manifold in place.
Green handles on front of meter are half-width disconnect handlesGreen handles on front of meter are half-width disconnect handles
AirPower™ 2 fan drive system
#

Enhanced air seeding performance would not be possible without the updates to the 15,152-L (430-bu) and 19,381-L (550-bu) 1910 and C850 Air Carts. For the wider seeding width, more fan capacity has been added.

 

AirPower 2 now provides two independently controlled fans – one for seed, one for fertilizer. Along with large 76.2-mm (3-in.) primaries, more accurate delivery rates are possible across the full width of the seeding tool – from opener to opener. Plus, AirPower 2 allows growers to deliver high rates under field operating conditions – up to 40 percent more product delivery per primary compared to the single-fan system.

 

Dual fans are required for tow-between and tow-behind carts on the 23.1-m (76-ft) tool with eight primaries. Each fan will direct air to one set of primaries. Two selective control valves (SCVs) are required for the fans. The fan speed will be controlled through the SCV flow control.

 

AirPower 2 will also be compatible with the current 17-m (56-ft) 1870, as well as the 13-m (43-ft) 1895, plus the 15.2- and 18.3-m (50- and 60-ft) 1890 models. An option is available for stainless-steel primaries – to resist corrosion from high fertilizer rates.

#

There is a slide at the meter to choose bottom or top shoot for each meter. There is also a valve on the tank pressure system to choose top or bottom shoot. This same valve is also used to adjust the amount of air to the tank to create the proper pressure differential.

#

The arrow on the valve handle should be pointing to the top of the range for the top shoot and the bottom of the range for the bottom shoot. If the tank will not be in use, set the pressure valve to the middle setting to not pressurize the tank. The operator should use the gauge to find the correct setting. An electronic pressure sensor will send a warning to the display if the tank pressure differential is out of range.

If pressure is in the green operating range, the tanks are sealed and operating correctly.

The electronic pressure sensor is located behind the mechanical gauge on the side of the cart.

 

Tank warnings on the GreenStar™ 3 230 Display*:
#

The operator will receive a warning in the display if a tank’s pressure is above or below normal working range. There will be a warning sign over the tank with the out-of-range issue.

Select the icon to view the tank pressure screen.

#

The operator can press on the red warning and get a screen that looks like the picture above. The plus indicates the pressure is out of range and could be delivering too much product.

#

The minus indicates the pressure is out of range and could be delivering too little product.

 

*Only applies to 1910 AirPower 2 Carts as the C850 Cart is only compatible with the Gen 4 CommandCenter™ display.

 

NOTE: A quick reference guide will ship with every operator’s manual. Please reference that and the operator’s manual for more detailed information.

Hydraulic drives provide accurate metering and variable rate
Hydraulic drives

Hydraulic drives are standard equipment on the 1910 air cart starting in model year 2014. They offer consistent drive power to the meters through all meter speeds. They offer many features, including variable-rate drive and hydraulic calibration as standard equipment.

 

The drive system reduces a large number of mechanical and electrical components including transmissions, clutches, chain drives, sprockets, gears, and shafts; replacing them with a hydraulic-drive motor, electrohydraulic valve, and a chain drive connecting the motor and meter.

 

Each meter has its own hydraulic drive motor and can be set independently of each other. It is recommended to use power beyond if available or another SCV, if power beyond is not available. The meter rotation is steady and smooth, minimizing pulsing effect. Drives are infinitely adjustable within range. The motor speed is controlled by an electrohydraulic valve mounted on the motor.

 

The operator has the ability to shut off all or any one or two of the given meters from the display at any given time. The operator has the ability to select from six different predetermined rates, or utilize variable rate for map-based prescriptions.

 

The system uses wheel speed from the cart to determine ground speed. If the cart wheel speed drops below 3.2 km/h (2 mph), the system will use tractor speed, if available, to maintain proper application rates when in turns or coming out of a headland turn.

Hydraulic drive motorHydraulic drive motor
#
Variable rate

Hydraulic variable-rate drive is standard equipment for 1910 Carts starting in model year 2014. Meter speeds will change from the slowest to the fastest meter speed almost instantaneously. This will improve the accuracy of variable-rate prescription applications where changing rates quickly are important to the operator.

Meter drive systemMeter drive system
Meter drive system with safety shield installedMeter drive system with safety shield installed
Hydraulic calibration

Hydraulic calibration is standard equipment for the 1910 Cart. Hydraulic calibration makes it easy for the operator to rotate the cart meters to perform easy and accurate calibration with very little effort from the operator.

 

Similar to the previous hydraulic calibration kit, the operator can calibrate more than one meter at a time. The first part of the procedure prompts the operator to prime the meters by giving the meter rollers two full rotations. The next step prompts the operator to turn the meters until they stop. After completing this step, enter the weight of the product caught during the latter step into the selectable boxes to get the new MDV.

Calibration tools and equipmentCalibration tools and equipment
Operator performing calibrationOperator performing calibration
Meter verification

Operators can now perform meter verification without driving. In the meter verification page on the display, select the meter(s) to verify and the stationary checkbox. When the operator engages the calibration switch, the meter will turn the number of revolutions to meter out the amount of product for the area selected.

 

NOTE: It is highly recommended to have power beyond and load sense installed on the tractor hydraulic system to power the hydraulic drives. This feature will save fuel, as well as reduce hydraulic heat, while providing maximum performance by the tractor hydraulic system to the cart hydraulic drive motors. By having load sense, the tractor is only required to provide the pressure and flow that the drives require. Power beyond and load sense capability have been tested and approved for all 8x00, 9x00, and newer John Deere tractors. Older John Deere tractors and competitive make tractors have not been tested for functionality.  If power beyond is not available, an additional SCV will be needed to power hydraulic drives. See link for more information on power beyond kits.

 

NOTE: Hydraulic drives cannot be retrofitted onto mechanical drive carts.

 

NOTE: For high application rates, it is recommended to utilize tractors with the hi-flow hydraulic pump option.  See 1910 Commodity Cart tractor compatibility and requirements for more information.

Stairway and platform offer convenience and easy access
Tow-between cart, front accessTow-between cart, front access
Tow-between cart, front accessTow-between cart, front access
Tow-behind cart, rear accessTow-behind cart, rear access
Tow-behind cart, rear accessTow-behind cart, rear access

 

 

The easy-to-navigate staircase and large platform provide easy access to tank lids. The staircase is much easier to navigate than ladders found on other air seeders.

 

On tow-between carts, there is convenient front access to the platform, with step-over access when going from side-to-side over the front hitch.

Specifications

Compare >>>

Select up to 2 models to compare specifications

John Deere1910 Tow-Behind Air Commodity Cart
Add Model
Add Model
Sizes
Tow-between model 2-tank
270, 350 bu
9531, 12355 L3-tank
250, 430 bu
8826, 15179 L
Tow-behind model 2-tank
270, 350 bu
9531, 12355 L3-tank
250, 340, 430, 550 bu
8810, 12002, 15179, 19381 L
Fan
Type Hydraulic motor, 26.5 USGPM @ 5000 psi max.
Size 44.7 (single), 66.04 (dual) cm
17.6 (single), 26 (dual) in.
Speed 2000 to 5000 rpm
Meter drives
Type Drive shaft
Variable rate drive Mechanical
Variable rate control Electric
Limp home mode Yes
Tanks
Type Translucent polyethylene
Lids Diameter Round: 67.31 cm
Diameter Round: 26.5 in.
Open-lid indicators Standard equipment
Meters
Meter rolls Up to 8 individual meter segments
Identify Color-coded meter rollers
Settings Infinitely variable 0-265 lb per acre
Half-width disconnect Yes
Fine-tuning rings Yes
Conveyance
Type Top drive hydraulic
Tires
Rear wheels and tires All-weather turf tread (standard)
Front wheels and tires
Ergonomics
Access Staircase with railing
Fill lights Standard
Freight
Shipping origin Valley City, ND

Accessories and Attachments

Air Packages for Seeding Tools

Eight Port Secondary Tower - BA31992
Eleven Port Secondary Tower - BA31995
Nine Port Secondary Tower - BA31993
Primary Air Package for 4 Run Tow-Behind - BA92240

Contact a John Deere dealer for information on primary run air packages for noncurrent seeding tools.

Primary Air Package for 6 Run Tow-Behind - BA92242

Contact a John Deere dealer for information on primary run air packages for noncurrent seeding tools.

Primary Air Package for 8 Run Tow-Behind - BA92244

Contact a John Deere dealer for information on primary run air packages for noncurrent seeding tools.

Seven Port Secondary Tower - BA31991
Ten Port Secondary Tower - BA31994
Twelve Port Secondary Tower - BA31996

Blockage

Blockage Sensors - 1 per Bundle - BA31271
Brackets, Wire Harness Guide - BA31326
Dual Module Bracket, 12 Member Module, 3 Harness - BA31279
Dual Module Bracket, 16 Member Module, 4 Harness - BA31280
Hardware, Fold Joint - BA31263
Harness, CAN Hitch No Blockage - Tow Behind - BA31272
Harness, Primary Blockage 16 Split - BA31269
Harness, Primary Blockage 8 Split - BA31268
ISO Blockage Main Components - Tow-Behind Cart - BA31651
Module and Harness Bracket, 10 Member Module, 3 Harness - BA31285
Module and Harness Bracket, 4 Member Module, 1 Harness - BA31282
Module and Harness Bracket, 5 Member Module, 2 Harness - BA31281
Module and Harness Bracket, 6 Member Module, 2 Harness - BA31283
Module and Harness Bracket, 8 Member Module, 2 Harness - BA31284

Conveyance

12 In. Conveyor for 250, 270 and 340 Bu. Cart - BA92750
Kits for conveyance systems
1910 Cart auger1910 Cart auger

Choose from two options when selecting the conveyance system for the 1910 Commodity Air Cart. Choose between an auger or conveyor. Fill time is less than 15 minutes and unloading time is less than 10 minutes. The lighting system at the hitch alerts the operator as to when the tank product levels are approaching full during a fill.

 

The auger is available with steel or brush flighting on all sizes, or cupped, to gently handle seed, which is available on the 8-inch auger only. These conveyance systems are recommended for beans and legumes, but not fertilizers.

NOTES:

  1. Hydraulic hose kit may be required.  If cart was originally ordered less auger (Option code 4595), then hydraulic hose kit is required.  For more information on hydraulic hose kits for conveyance systems, please consult: conveyance hydraulic hose attachments
  2. Conveyance swing arm system may be required. When adding a conveyor to a 1900 Cart OR to a 1910 Cart prior to serial numbers (A01910T700346 Tow-Between or A01910H700409 Tow-Behind), an arm system is required.  When adding an auger attachment to a 1900 Cart or 1910 Cart prior to serial numbers (A01910T700346 tow-hetween or A01910H700409 Tow-Behind), an arm system is required due to changes in latching system.  Tow-between 1910 Carts above serial number (A01910T700346) and tow-behind carts above serial number (A01910H700409) do not require updates to arm system.  Please consult conveyance arm attachments for additional ordering information.
  3. All 7-in. and 8-in. auger attachments require A60206 auger hopper from Service Parts.
  4. 7-in. and 8-in. augers do not include downspouts.  For a 7-in., flexible downspout, order (1)A61684 tube and (2) TY22495 clamps from Service Parts.  For a 8-in. flexible downspout, order (1) A60207 tube and (2) TY22497 clamps from Service Parts.  For a telescopic spout for 8-in. augers, please consult telescoping spout attachments for field conversion.  12-in. conveyors have a telescopic spout included in the bundle as standard equipment.
8 In. Steel Flight Auger for 250, 270 and 340 Bu. Cart - BA29967
Auger Arm Kit for 250, 270 and 340 Bu. Cart - BA92791
Swing arm kit
1910 Cart auger1910 Cart auger

The swing link arm allows for better movement with the redesigned pivot. It has a larger ''sweet spot'' for easier movement and placement of the hopper.

NOTE: Required if cart was previously ordered without an auger/conveyor system (code 4595).
Conveyor Arm System - BA92752
Swing arm kit
1910 Cart auger1910 Cart auger

The swing link arm allows for better movement with the redesigned pivot. It has a larger ''sweet spot'' for easier movement and placement of the hopper.

NOTE: Required if cart was previously ordered without an auger/conveyor system (code 4595).

Delivery

Meter Run Reduction Kit - BA32812

SectionCommand™ is available as an attachment for field conversion (AFC) for all hydraulic drive carts.  See SectionCommand saves seed and fertilizer input costs for more information on benefits and workings of the system.

SectionCommand components on 1910 cart with meter cartridge removedSectionCommand components on 1910 cart with meter cartridge removed
SectionCommand on 1910 air cartSectionCommand on 1910 air cart

There are 4 main components needed to add SectionCommand™ onto 1910 hydraulic drive air carts:

 

1. SectionCommand™ AFC kit (listed in the table below, order one kit per meter), kit includes:

  • SectionCommand™ valve block and meter housing components
  • Gate detection controller
  • Electronic power module (EPM)
  • Associated harnessing, hardware, and brackets

2. Hydraulic hoses - Dealer is responsible for fabricating and sourcing hoses.

 

3. SectionCommand™ meter cartridges will be needed for each meter. These meter cartridges contain gates, gate detection sensors and a secondary meter lock-down. See Meter cartridges for field conversion for more information.

 

4. New Operator’s Manual including SectionCommand™. Order A98462 or newer 1910 operator’s manual when installing onto a model year 2013 550 bu cart or all model year 2014 carts.

 

Ensure latest version of software is installed on both cart controller and in-cab display.

 

All SectionCommand™ kits are sold in 8-run configurations.  If pairing the cart with a tool 7 runs or less, order 1 - BA32812 Meter run reduction kit per cart.  This kit contains parts to block off runs not used when pairing a cart with a tool of 7 runs or less.

 

Electrical

CAN Transition Bridge - BA28777

The 7-pin extension harness attaches to the seeding tool. It supplies power to the 1910 Cart meter clutches and monitor system. It also supplies power to the seeding tool warning lights and cart warning lights.

The CAN extension harness is for the SeedStarTM monitor. It assembles to the seeding tool and connects from the front of the cart to the back of the tractor.

 

Notes:

  1. May be required for tow-behind carts attached to non-John Deere seeding tools.
  2. Monitor and 7-pin extension harnesses are normally supplied with John Deere seeding tools.
  3. Will not be needed if the air package is ordered with the seeding tool as a code.

Frame

Hitch - Cart Rear for 270 or 340 Bu. Tow Behind Cart - BA32776
Rear hitchRear hitch

The rear hitch is used with tow-behind carts and has 22,000-lb towing capacity. The rear hitch allows connecting another implement to the cart, such as a coil-type packer or harrow.

Hitch - Yard for Tow-Behind 1900/1910 Cart - BA32302

Handling

Tank Lid Screen - BA29518

Hydraulics

Flow Through Hydraulic Hose Kit - 1895 and Tow Behind Cart - BA31176
TBH cart with tool and tractorTBH cart with tool and tractor
#

See link below for information on seeding tool and TBH cart compatibility.


1910 Tow-Behind Cart and seeding tool compatibility

 

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.


Hydraulic drive cart requirements for software, hydraulic and electrical overlays 

 

The following table outlines hydraulic hose overlay AFC kits available for:

  1. Power beyond, return, and load sense for hydraulic drive and SectionCommand™
  2. Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

 

Model 2013 and older tools did not have power beyond, return, and load sense hoses installed except for when paired with a 550 bu TBH cart.  If pairing a model year 2013 or older tool with a TBH cart, hoses for power beyond, return, and load sense will need installed and can be seen below.

Flow Through Hydraulic Hose Kit - All Tools Except 1895 and Tow Behind Cart - BA31175
TBH cart with tool and tractorTBH cart with tool and tractor
#

See link below for information on seeding tool and TBH cart compatibility.


1910 Tow-Behind Cart and seeding tool compatibility

 

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.


Hydraulic drive cart requirements for software, hydraulic and electrical overlays 

 

The following table outlines hydraulic hose overlay AFC kits available for:

  1. Power beyond, return, and load sense for hydraulic drive and SectionCommand™
  2. Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

 

Model 2013 and older tools did not have power beyond, return, and load sense hoses installed except for when paired with a 550 bu TBH cart.  If pairing a model year 2013 or older tool with a TBH cart, hoses for power beyond, return, and load sense will need installed and can be seen below.

Flush Face Motor Case Drain Coupler for 30-60 Series Row Crop Tractors and 30-50 Series 4-Wheel Drive Tractors - BA30132
Flush face case drain couplerFlush face case drain coupler

For installing tractor case drain for vacuum motors. A motor seal drain kit (return to sump) protects the motor and shaft seal by allowing motor housing pressure to return back to hydraulic reservoir free of any back pressure. Handles up to 3 U.S. gallons per minute.

 

NOTE: All vacuum planters built after 1 May 2004 have hydraulic case drain vacuum motors. These motors have a flush-face case drain hose tip on the return oil line that must be routed to the tractor's sump/case drain port. The tractor requires a case drain coupler be installed in this port to accept the return hose. 

 

This kit is required for operation of 1910 Commodity Air Cart and 1990 CCSTM hydraulically-driven fan.

Flush Face Motor Case Drain Coupler for 60-70 Series 4-Wheel Drive Tractors - BA30133
Flush face case drain couplerFlush face case drain coupler

For installing tractor case drain for vacuum motors. A motor seal drain kit (return to sump) protects the motor and shaft seal by allowing motor housing pressure to return back to hydraulic reservoir free of any back pressure. Handles up to 3 U.S. gallons per minute.

 

NOTE: All vacuum planters built after 1 May 2004 have hydraulic case drain vacuum motors. These motors have a flush-face case drain hose tip on the return oil line that must be routed to the tractor's sump/case drain port. The tractor requires a case drain coupler be installed in this port to accept the return hose. 

 

This kit is required for operation of 1910 Commodity Air Cart and 1990 CCSTM hydraulically-driven fan.

Hydraulic Hose Kit with Power Beyond, Return and Load Sense - 1895 and Tow Behind Cart - BA32686
TBH cart with tool and tractorTBH cart with tool and tractor
#

See link below for information on seeding tool and TBH cart compatibility.


1910 Tow-Behind Cart and seeding tool compatibility

 

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.


Hydraulic drive cart requirements for software, hydraulic and electrical overlays 

 

The following table outlines hydraulic hose overlay AFC kits available for:

  1. Power beyond, return, and load sense for hydraulic drive and SectionCommand™
  2. Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

 

Model 2013 and older tools did not have power beyond, return, and load sense hoses installed except for when paired with a 550 bu TBH cart.  If pairing a model year 2013 or older tool with a TBH cart, hoses for power beyond, return, and load sense will need installed and can be seen below.

Hydraulic Hose Kit with Power Beyond, Return and Load Sense - All Tools Except 1895 and Tow Behind Cart - BA32685
TBH cart with tool and tractorTBH cart with tool and tractor
#

See link below for information on seeding tool and TBH cart compatibility.


1910 Tow-Behind Cart and seeding tool compatibility

 

See link below for information on hydraulic, electrical, and software requirements for pairing hydraulic drive carts with model year 2013 and older seeding tools.


Hydraulic drive cart requirements for software, hydraulic and electrical overlays 

 

The following table outlines hydraulic hose overlay AFC kits available for:

  1. Power beyond, return, and load sense for hydraulic drive and SectionCommand™
  2. Fan power, return, and case drain

All model year 2014 and newer tools paired with TBH carts are shipped from the factory with overlay hoses for both number’s one and two from above.

 

Model 2013 and older tools did not have power beyond, return, and load sense hoses installed except for when paired with a 550 bu TBH cart.  If pairing a model year 2013 or older tool with a TBH cart, hoses for power beyond, return, and load sense will need installed and can be seen below.

Metering

Non-SectionCommand Meter Roller - High Rate (Green) - 30 to 220 Lb. Per Acre - BA29096

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand
Non-SectionCommand Meter Roller - Low Rate (Yellow) - 2 to 20 Lb. Per Acre - BA29094

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

Non-SectionCommand Meter Roller - Regular Rate (Black) - 20 to 130 Lb. Per Acre - BA29095

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

Non-SectionCommand Meter Roller - Very High Rate (Blue) - 40 to 265 Lb. Per Acre - BA29097

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

SectionCommand Meter Roller - High Rate (Green) - 30 to 220 Lb. Per Acre - BA32679

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

SectionCommand Meter Roller - Large Seed (Orange) Meter Roller - 35 to 240 Lb. Per Acre - BA32683

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

SectionCommand Meter Roller - Low Rate (Yellow) - 2 to 20 Lb. Per Acre - BA32675

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

SectionCommand Meter Roller - Regular Rate (Black) - 20 to 130 Lb. Per Acre - BA32677

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

SectionCommand Meter Roller - Very High Rate (Blue) - 40 to 265 Lb. Per Acre - BA32681

There are five types of meter cartridges available to match seed and fertilizer types and rates.

Low rate
Low-rate meter rollerLow-rate meter roller

The yellow, low-rate meter roller is for rates from 0.91 up to 9.07 kg/ha (2 up to 20 lb/acre) for seeds such as flax, canola, and alfalfa. The low-rate meter roller rotates more continuously, minimizing pulsing effect for better metering at low rates. There are 20 flutes on this meter roller. Each flute is 8 mm (0.31 in.) wide at top x 2 mm (0.08 in.) wide at bottom x 1.5 mm (0.06 in.) deep.

Medium rate
Medium-rate meter rollerMedium-rate meter roller

The black medium-rate meter roller is for rates from 9.07 up to 59 kg/ha (20 up to 130 lb/acre) for seeds such as wheat, barley, canola, and small soybeans up to 6.35 mm (0.25 in.) in diameter. It is also used for medium rates of fertilizer. This is the most commonly used meter roller. There are 10 flutes on this roller, which are 18.5 mm (0.73 in.) wide at top of flute x 12 mm (0.47 in.) at bottom of flute x 8 mm (0.31 in.) deep.

High rate
High-volume meter rollerHigh-volume meter roller

The green, high-volume meter roller is for rates from 30 up to 99.8 kg/ha (220 lb/acre), such as high rates of fertilizer and large soybeans bigger than 6.35 mm (0.25 in.) in diameter. There are 10 flutes, which are deeper and wider. Each flute is 21.5 mm (0.85 in.) wide at top of flute x 8 mm (0.31 in.) wide at bottom of flute x 14 mm (0.55 in.) deep.

Very high rate
Very-high-rate meter rollerVery-high-rate meter roller
This blue roller is for rates from 22.7-120.2 kg/ha (50-265 lb/acre), or seeds such as barley and oats with beards. It is also used for large seeds such as garbanzo beans (in non SectionCommand™ applications) or very high fertilizer rates. There are 6 flutes, which are very deep and widely spaced.
Large-seed roller for SectionCommand
Large seed meter rollerLarge seed meter roller
#
  • For use with large seeds only (6 mm [0.25 in.] in diameter or larger)
  • For use with SectionCommand only
  • Is not for use with fertilizers or cereal grains
  • Preserves seed quality of large seeds when used with SectionCommand

The width of the seeding tool and the number of furrow openers determine the number of active primary ports. The commodity cart can be equipped with a 3, 4, 5, 6, 7, or 8-run meter roller. One meter roller is required for each tank on the 1910.

 

When outfitting a cart with SectionCommand, new SectionCommand meter cartridges with gates and gate detection equipment will be needed.  See table below for meter cartridges.

 

NOTE: When metering high rates through a seeding tool with three to four secondary manifolds, it may be necessary to either add secondary manifolds or slow down to achieve a very high target rate.

Seed/Fertilizer Rate Control, Two Tanks - BA31303
Variable seed rateVariable seed rate

Variable seed rate capability allows the operator to vary seed/fertilizer rate on-the-go from the tractor cab. The operator can choose from one to six rates per tank. This provides precision farming with SeedStarTM monitor control and the GreenStarTM display.

 

The variable-rate drive system is also compatible with Ag Management Solutions products Field DocTM Air Cart for data logging, as well as Map Based Prescriptions, to enable the operator to use predefined product application rates that automatically switch on-the-go.

 

Please consult Ag Management Solutions price pages for ordering information for Field DocTM and Map-Based Prescriptions.

SectionCommand

SectionCommand Valve Block and Associated Parts - One per Meter - BA32805

SectionCommand™ is available as an attachment for field conversion (AFC) for all hydraulic drive carts.  See SectionCommand saves seed and fertilizer input costs for more information on benefits and workings of the system.

SectionCommand components on 1910 cart with meter cartridge removedSectionCommand components on 1910 cart with meter cartridge removed
SectionCommand on 1910 air cartSectionCommand on 1910 air cart

There are 4 main components needed to add SectionCommand™ onto 1910 hydraulic drive air carts:

 

1. SectionCommand™ AFC kit (listed in the table below, order one kit per meter), kit includes:

  • SectionCommand™ valve block and meter housing components
  • Gate detection controller
  • Electronic power module (EPM)
  • Associated harnessing, hardware, and brackets

2. Hydraulic hoses - Dealer is responsible for fabricating and sourcing hoses.

 

3. SectionCommand™ meter cartridges will be needed for each meter. These meter cartridges contain gates, gate detection sensors and a secondary meter lock-down. See Meter cartridges for field conversion for more information.

 

4. New Operator’s Manual including SectionCommand™. Order A98462 or newer 1910 operator’s manual when installing onto a model year 2013 550 bu cart or all model year 2014 carts.

 

Ensure latest version of software is installed on both cart controller and in-cab display.

 

All SectionCommand™ kits are sold in 8-run configurations.  If pairing the cart with a tool 7 runs or less, order 1 - BA32812 Meter run reduction kit per cart.  This kit contains parts to block off runs not used when pairing a cart with a tool of 7 runs or less.

 

SectionCommand Valve Block and Associated Parts - One per Meter - BA32692

SectionCommand™ is available as an attachment for field conversion (AFC) for all hydraulic drive carts.  See SectionCommand saves seed and fertilizer input costs for more information on benefits and workings of the system.

SectionCommand components on 1910 cart with meter cartridge removedSectionCommand components on 1910 cart with meter cartridge removed
SectionCommand on 1910 air cartSectionCommand on 1910 air cart

There are 4 main components needed to add SectionCommand™ onto 1910 hydraulic drive air carts:

 

1. SectionCommand™ AFC kit (listed in the table below, order one kit per meter), kit includes:

  • SectionCommand™ valve block and meter housing components
  • Gate detection controller
  • Electronic power module (EPM)
  • Associated harnessing, hardware, and brackets

2. Hydraulic hoses - Dealer is responsible for fabricating and sourcing hoses.

 

3. SectionCommand™ meter cartridges will be needed for each meter. These meter cartridges contain gates, gate detection sensors and a secondary meter lock-down. See Meter cartridges for field conversion for more information.

 

4. New Operator’s Manual including SectionCommand™. Order A98462 or newer 1910 operator’s manual when installing onto a model year 2013 550 bu cart or all model year 2014 carts.

 

Ensure latest version of software is installed on both cart controller and in-cab display.

 

All SectionCommand™ kits are sold in 8-run configurations.  If pairing the cart with a tool 7 runs or less, order 1 - BA32812 Meter run reduction kit per cart.  This kit contains parts to block off runs not used when pairing a cart with a tool of 7 runs or less.

 

Wheel Equipment

Dual Tire Conversion - BA92501
Dual tire conversion kitDual tire conversion kit

The rear duals conversion kit allows converting carts equipped with 20.8R-38 R1, 20.8R-42 and 18.4-26 10 PR R3 tires from single wheels to duals.

 

Bundle includes two wheel spacers (AA44677) for rear cart tires which will move each tire 7.75-in. from center.

 

Two warning light bracket extensions (left- and right-hand side) are also included.

 


 

Rear dual tire spacings
 TiresSpacing: Centerline to centerline  
 Duals - Inner tires 120.6 in. (3062 mm)
 Duals - Outer tires 176.6 in. (4485.8 mm)

 

IMPORTANT: Rear duals are recommended on slopes from 10-15 degrees.

Two 16.5L-16.1 In. 6 PR I-3 - BA27841

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.
Two 20.8R-38 In. One Star R1 - BA27198

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.
Two 20.8R-42 In. Two Star R1 - BA28356

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.
Two 21.5L-16.1 In. 8 PR I-3 - BA27842

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.
Two 28L-26 In. 12 PR R3 - BA27835

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.
Two  710/70R-38 In.  Two Star  R1W - BA27197

A wide choice of tires and wheels is available for field installation to match soil and residue conditions.

 

For more information on tire options, please see 1910 Wheel and Tire Options.

 

Single rear-tire spacing—all carts

 

 

 

 Tires

 Tread spacing—centerline to centerline

 18.4-26

 3.47 m (136.6-in.)

 23.1-26

3.44 m (135.6-in.) 

 28L-26

3.44 m (135.6-in.) 

 30.5L-32

 3.44 m (135.6-in.)

710/70R38 (code 3012)

3.44 m(135.6-in.)

 710/70R38 (code 3010)

3.0 m (118-in.) 

 

Dual rear-tire spacing—all carts

 

 

 Tires

Tread spacing—centerline to centerline 

 18.4R42

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R38

 

 Inner tire

3.06 m (120-in.) 

 Outer tire

4.57 m (180-in.) 

  20.8R42

 

 Inner tire

3.06 m (120-in.) 

 

 Outer tire

4.57 m (180-in.) 

 

NOTES:

  1. If tires are changed on the cart, the drive sprocket must match.
  2. Includes TWO tires and wheels and tire circumference sprockets.